A S tudy of Fatigue Properties of Steel AISI4130 (30KhMF) after Upset W elding 55. 50 m m. 50 m m. 50 m m. 4140 Alloy Steel - 4140 Alloy Steel Alternative Superior Steel Alternative to. 4140 Alloy Steel. Pennsylvania Steel Corporation presents an alternative to SAE 4140 alloy steel. FLEXOR®'s chemistry and mechanical properties are comparable, if not superior to 4140 alloy steel and thusly, can be utilized in most of the same applications.
Typical Properties. AISI 4140 and 4150 is a medium carbon, chromium-molybdenum alloy steel. This steel is offered in a wide range of conditions including but not limited to:cold drawn annealed, hot roll heat treated, heat treated turned ground and polished. Typical tensile strength ranges from 114,000 PSI (Annealed Condition) up to 156,000 PSI (Pre-Hard, Quench and Tempered Condition). 4140 Steel Associated Steel Corporation4140 Steel, Annealed 4140, Prehard 4140, 4140 Turned Ground & Polished, 4140 Flats, 4140 Squares, 4140 Hexagons, 4140 Rounds. Also 4150 Steel. 4140 steel round bar SAE4140 forging steel 4140 Chrome 4140 steel can be hot worked at 816 to 1038°C. Cold Working AISI 4140 alloy steel can be cold worked using conventional methods in the annealed condition. Annealing AISI 4140 steel is annealed at 872°C followed by slowly cooling in the furnace. Tempering 4140 alloy steel can be tempered at 205 to 649°C depending upon the desired hardness level.
Figure 9 (Mechanical Properties for 4140 and 4140HW) The data represents a mechanical property comparison of several 4140 and 4140HW heats. Figure 10 (Jominy Hardenability Curve for 4140 and 4140HW) The data represents an average of Jominy results from several 4140 and 4140HW heats. For more information, visit timkensteel or call us AISI 4140 Alloy Steel (UNS G41400) - theenzoneAISI 4140 alloy steel is chromium, molybdenum, manganese containing low alloy steel. It has high fatigue strength, abrasion and impact resistance, toughness, and torsional strength. The following datasheet gives an overview of AISI 4140 alloy steel. Chemical Composition The following table shows the chemical composition of AISI 4140 alloy steel. AISI 4140 Steel, normalized at 870°C (1600°F), air cooled AISI 4140 Steel, normalized at 870°C (1600°F), air cooled, 13 mm (0.5 in.) round Categories:Metal; Ferrous Metal; Alloy Steel; AISI 4000 Series Steel; Low Alloy Steel; Carbon Steel; Medium Carbon Steel. Material Notes:Normalized:heated to 815°C, air cooled.
And the equivalent grade for it is DIN 1.7225 and JIS SCM440. 4140 Steel properties and heat treat as below. AISI 4140 Steel Characteristics. It is low alloy steel with chromium, molybdenum, and manganese. Great toughness, fatigue strength, abrasion and impact resistance. It is widely be used in the industry due to its excellent versatility and Datasheet 4340 ALLOY STEEL AMS 6414 VAR 4340 ALLOY STEEL AMS 6414 VAR UNSG43406 DATA SHEET GENERAL CHARACTERISTICS:4340 VAR AMS 6414 is a low alloy Chromium-Nickel-Molybdenum steel capable of being heat treated to high strength levels. This specification is for a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock. Fatigue behavior of a 4140 steel coated with a NiMoAl The fatigue behavior of a quenched and tempered AISI 4140 steel has been investigated in three different conditions:as-polished, as-grit blasted with Al 2 O 3 particles and as-coated, after grit blasting, with a deposit of NiAlMo alloy (Metco 447) of approximately 300 m in thickness, applied by HVOF thermal spraying. It has been determined that after grit blasting with particles of 20
Jan 19, 2007 · In this specific case, there is a published or test value that was used instead of a default value (like fatigue strength= 0.5 * UTS). Certain metals can exhibit hardening or softening behavior under cyclic loading versus monotonic loading conditions. Fatigue-Proof - Cold Finished Steel Bar ManufacturerFatigue-Proof® is definitely a freemachining steel. Although it has hightensile strength andhardness properties usually associated onlywithheattreated steels, it is an excellent machining material. For example, Fatigue-Proof® is rated at 80% of 1212 and will How to weld AISI 4140 Steel Material WeldingAISI 4140 is a Cr-Mo-Mn based high strength low alloy steel offering high fatigue strength, toughness, abrasion & impact resistance. Being a medium carbon steel range, AISI 4140 gets hardened during welding repair especially in the heat affected zones (HAZ) due to thermal cycles and microstructural transformation along with locked residual stresses produced by the welding heat.
Feb 09, 2016 · The Effects of Sulfur on the Fatigue Properties of Low Alloy Steels Posted on February 9, 2016 by Steel Market Development Institute It is well known that sulfur has a major impact on some of the properties of low alloy steels. SAE-AISI 4140 Steel vs. SAE-AISI 4340 Steel ::MakeItFromMay 30, 2020 · Both SAE-AISI 4140 steel and SAE-AISI 4340 steel are iron alloys. They have a very high 98% of their average alloy composition in common. For each property being compared, the top bar is SAE-AISI 4140 steel and the bottom bar is SAE-AISI 4340 steel. Steels - Endurance Limits and Fatigue Stress1 MPa = 10 6 Pa = 1 N/mm 2 = 145.0 psi (lbf/in 2); Fatigue limit, endurance limit, and fatigue strength are used to describe the amplitude (or range) of cyclic stress that can be applied to the material without causing fatigue failure.; Creep. The time dependent deformation due to heavy load over time is known as creep.. In general both stress and temperature influence on the rate of creep
Oct 24, 2011 · However, you did not mention the heat treatment condition of the 4140 earlier because using the stress life (S/N) approach, strength has a direct effect on the shape and magnitude of the S/N curve. So, what you need is stress-life fatigue data for normalized 4140 alloy steel. Let me see what I can find in my reference material. SAE AISI 4140 Steel Properties, Material Heat Treatment SAE 4140 (AISI 4140 steel) is a Cr-Mo series (Chrome molybdenum series) low alloy steel, this material has high strength and hardenability, good toughness, small deformation during quenching, high creep strength and long-lasting strength at high temperature.