ASTM A242 HSLA steel is an alloy steel formulated for primary forming into wrought products. Cited properties are appropriate for the as-fabricated (no temper or treatment) condition. ASTM A242 is the defining standard for this material. Additionally, the UNS number is K11510. It has a very low base cost among wrought alloy steels in the same ASTM A242 Type 2 Plates, A242 Type 2 Corten Steel PlatesASTM A242 Type 2 Corten Steel Plate Specification :Grade :ASTM A242 Type 2 Corten Steel Plates Standard :ASTM A242 / ASME SA242 Width :1500mm to 4050mm, Length :3000mm to 15000mm Thickness :6MM to 200 Type :Weathering Steel / Weather Resistant / Corten Steel / High-Strength Low-alloy Structural Steel Process :Hot-Rolled (HR)
This specification covers high-strength low-alloy structural steel shapes, plates, and bars for welded, riveted, or bolted construction intended primarily for use as structural members where savings in weight [mass] or added durability are important. such as those described in Specifications A242/A242M, A588/A588M, A606 Type 4, ASTM A588 - SSABThe ASTM A588 specification is the Standard Specification for High-Strength Low-Alloy Structural Steel , up to 50 ksi Minimum Yield Point, with Atmospheric Corrosion Resistance for applications where strength and durability are needed. The required ASTM G101 Corrosion Resistance Index must be 6.0. ASTM A588 Corrosion-Resistant Structural Steel Plate Material Properties The following material properties are ASTM specifications and will be confirmed on the Mill Test Report. Thickness Yield Point (ksi) Tensile Strength (ksi) Min. 2 Elongation % 4 in. and under 50 70 21 Over 4 in. to 5 in. 46 67 21 Over 5 in. to 8 in. 42 63 21 Chemical Composition The following composition properties are ASTM specifications for these A588 grades. A Carbon
Material Properties The following material properties are ASTM specifications and will be confirmed on the Mill Test Report Grade Yield Point (ksi) Tensile Strength (ksi) Min. 2 Elongation % Type II & IV As-rolled 50 70 22 Type II & IV Annealed or normalized 45 65 22 Chemical Composition The following composition properties are ASTM specifications for these A606 grades. Note that ASTM Weathering Steel Specifications Central Steel ServiceASTM A242 is a high strength low-alloy structural steel specification with improved atmospheric corrosion resistance. This specification is normally applicable to steel Buy Weathering Steel-Corten A|A709|A242M|A588 From Product Description:The applicable equivalent ASTM specifications for weathering steel are ASTM A588, ASTM A242, ASTM A606-4, ASTM A847 and ASTM A709-50W, other standards JIS G3125, JIS G3114, EN10025 and GB/T4171.AGICO-ANSON STEEL supplies various products including, steel sheet, steel coil, steel plate, steel flats, angles, channels.
Amardeep Steel Is One Of The Leading Exporter,Supplier,Stockist And Manufacturer Of Corten Steel ASTM A242 Type 1 Plate & Sheet.Amardeep Steel Has Ready Stock Of Corten Steel ASTM A242 Type 1 Plate & Sheet To Serve Your Requirements .We Offer Quickest Delivery Of Corten Steel ASTM A242 Type 1 Plate & Sheet At Lowest Price Without Any Compromise On Our Quality. High Quality Weathering Steel Plate-ASTM A242 Type 1 ASTM A242 Type 1 Steel Plate. AGICO-ANSON manufactures high quality weathering steel-ASTM A242 steel plate, ASTM A242 specification is made for low alloy steel with high strength, it has good atmospheric corrosion resistance, some applications has shown that it has better corrosion resistance than ASTM A36 steel plate and ASTM A572 Grade 50. The same as weathering steel, it can be used High Strength Weathering Steel Sheets Central Steel ServiceCentral Steel Service, Inc. stocks ASTM A606-4 steel sheet and coil, which are considered the ASTM applicable equivalents to Cor-Ten®. Visit our site to learn more! Call us today at 800.868.6798
ASTM A242 is the standard specification for carbon and low alloy and high strength structural steel plate. The specification covers high strength steel profiles, plates and bars for welded, riveted, or bolted constructions. It usually been used to save the weight or increase the durability in steel constructions. Protective STEEL SPECSTEEL SPEC FAST DRY ALKYD TOPCOAT B55-800 SERIES Protective & Marine Coatings 2.19 PRODUCT DESCRIPTION Steel Spec Fast Dry Alkyd is a one component modi ed alkyd. Ideal for use in fabrication shops Formulated for fast drying and curing Recoat in 1 hour Allows multiple coats to be applied during one shift. Questions About Corten Central Steel ServiceWeathering steels, such as ASTM A588, A242, A606-4 and Cor-Ten® exhibit superior corrosion resistance over regular carbon steel as a result of the development of a protective oxide film on the metals surface which slows down further corrosion.Their 50,000 minimum yield strength characteristic allows cost reduction through the ability to design lighter sections into structures.
Steel Spec Universal Primer. A single-component, weldable, rust-inhibitive universal primer. A heavy-duty primer that combines many features of highly specialized primers into one product, Steel Spec Universal Primer can be topcoated with epoxy, vinyl, chlorinated rubber, alkyd, acrylic and urethane coatings, as well as conventional oil and oleoresinous paints. This enables structural steel Tubeco, Inc. SpecsASTM A242. High strength low alloy steel plate for weathering steel. Specification for HSLA steel with increased atmospheric corrosion resistance. This spec was the original when Cor-Ten was introduced. It covered plate up to ½ in thickness. Not commonly used anymore, refer to A588. View details » Weathering steel in architectural applications.ering steel. Interestingly, the plaza outside the Daley Center features a Pablo Picasso sculpture also made entirely of weathering steel. Specification Specifics ASTM A588 covers the majority of rolled structural shapes produced in weathering steel and can be con-sidered the base specification for weathering steel for
The ASTM A242 specification is the standard specification for high-strength low- alloy structural steel for structural members where weight savings and atmospheric corrosion resistance are important. Mechanical property requirements are specified by product type (plates and bars, and structural Shapes) and by thickness.